DIY Christmas Jewelry Ideas with Vogue Elements Laser Materials

Looking to add handmade charm to your holiday outfits?

This collection of DIY Christmas jewelry ideas has everything needed to sparkle this holiday season!

From adorable snowman earrings to matching necklace and bracelet sets, there's something for everyone.

Plus, a free laser SVG file that will make crafting even easier!

Craft Video Tutorial

Do you like videos? I have a video tutorial for you! Subscribe to my YouTube Channel so you don't miss any future videos.

Craft Closet Vogue Elements

Some supplies were provided at no cost. If the exact supplies are unavailable, links may lead to similar products.

All materials used today are from the Vogue Elements Whimsy Christmas Collection by Craft Closet.

All materials are double-sided and have a thickness of 1/16-inch.

I will use different products from this line in each jewelry tutorial, and I am so excited to share what I created!

Grab the Free Laser File

Download the free SVG laser file to your computer or device. You will receive the file without the watermark overlay.

Matching Necklace and Bracelet

Supply List

• Laser Cutting Machine
• Holiday Jewelry Bundle
• Reflections Christmas Ball
• Reflections Silver
• Clasp - for bracelet
• Jump Rings
• 2 pairs of Jewelry Pliers

This Reflections material is only compatible with CO2 laser but will not work in a diode machine.

Instructions

Upload the file to your laser machine software and cut.

The file only includes one shape for the necklace or bracelet, so you can cut as many or as few as you want. I cut 21 from each sheet.

This material is double-sided and has a plastic film on both sides.

Remove the plastic film after the pieces have been cut to protect the finish.

After the film has been removed, the pieces become much more reflective. In the image below, only half of the pieces have been weeded. Can you tell which?

After the film has been removed from both sides, begin assembly.

Start with an open jump ring and slide on one oval of each color.

Then, close the jump ring.

The correct way is to grab each side with pliers and twist the wrist to close. If the wrists are pushed together, the ring will become misshapen.

The chain is now started.

Hold an open jump ring in a pair of pliers to continue the chain.

Slide on the end of the chain and the opposite color oval piece.

Twist the wrists to close the jump ring, and repeat. The longer the chain, the more pieces are added.

Necklace

The necklace can be any length you want. I wanted it to be just long enough to fit over my head.

After making what I thought was a long enough strand, I held the ends together and tried to put it over my head.

It is perfect!

To end the necklace, make sure each end is a different color, place them on a jump ring, and twist close.

The necklace is finished!

Bracelet

The bracelet doesn't take as many pieces, but the assembly is the same as the necklace.

I tested the length by wrapping the strand around my wrist, and 10 pieces fit perfectly.

Grab two 2mm jump rings and one 3mm jump ring.

On a 2mm jump ring, slide on the end of the bracelet and the clasp.

Twist to close the jump ring.

Close the 3mm jump.

On the other 2mm jump ring, slide on the end of the bracelet and the closed 3mm jump ring.

The bracelet is now finished! Isn't this such a pretty set? Perfect for any holiday party.

Mixed Material Earrings

Supply List

• Laser Cutting Machine
• Holiday Jewelry Bundle
• Pressed Patterns Peppermint Stripe
• Luxe Leather Vanilla Glaze
• Earring Hooks
• 8 2mm Jump Rings
• 2 pairs of Jewelry Pliers

Luxe Leather and Pressed Patterns are compatible with the CO2 and Diode lasers.

Instructions

Upload the file to your laser machine software and cut.

To attach the wood piece to the leather piece, lay the wood piece on top of the leather piece with the top hole facing down.

Insert jump rings into the side holes of both materials and twist the wrists to close the jump rings.

When attached correctly, the hole will be empty and on the top.

Insert a jump ring into the top hole, slide on the earring hook, and close the jump ring.

One earring is done. Just repeat for the second earring.

These DIY earrings are so cute and come together really quickly!

Braided Bracelet

Supply List

• Laser Cutting Machine
• Holiday Jewelry Bundle
• Glam Flex Pearl Glitter
• Ribbon End Clamps
• 2 pairs of Jewelry Pliers
• Scissors
• Spring Clamp

This Glam Flex material is compatible with both CO2 and diode laser machines.

Instructions

Upload the file to your laser machine software and cut.

This material is double-sided and has a plastic film on both sides.

Remove the plastic film after the pieces have been cut, and the material becomes much more flexible.

The cut piece has a joined end and three tails. Begin at the joined end and braid the three tails.

Right over center, left over center, and so on until the end of the tails is reached.

I used a spring clamp to hold the ends of the braid, freeing up my hands to prepare the ribbon end clamps.

My ribbon clamps came with chains and the clasp attached. I found it much easier to remove those parts before attaching them to the braided piece.

Opening a jump ring is the same as closing. Just twist the wrists in opposite directions.

Trim the ends of the braided pieces so the ends are even.

Slide the clamp over the ends and tighten to secure. The ribbon clamps have teeth that dig in and hold.

For the other side of the bracelet, cut off the solid end, slide on the other ribbon clamp, and squeeze to secure.

Reattach the jump rings and clasps to the end clamps, and the braided bracelet is ready to wear!

Snowman Earrings

Supply List

• Laser Cutting Machine
• Holiday Jewelry Bundle
• Willows Hickory
• Earring Hooks
• 4 2mm Jump Rings
• 2 pairs of Jewelry Pliers

Willows materials are compatible with CO2 and Diode lasers.

Instructions

Upload the file to your laser machine software and cut.

Start with an open jump ring, slide on a snowman shape, and close.

On the second jump ring, slide on the ring with the snowman and an earring hook, and then close the ring.

The first earring is done. Repeat for the second, and these snowman earrings are ready to impress!

Layered Tree Earrings

Supply List

• Laser Cutting Machine
• Holiday Jewelry Bundle
• Luxe Leather Lime Potion
• Luxe Leather Green Envy
• Earring Hooks
• 2 2mm Jump Rings
• 2 4mm Jump Rings
• 2 pairs of Jewelry Pliers

Luxe Leather is compatible with the CO2 and Diode lasers.

Instructions

Upload the file to your laser machine software. Divide the tree earring file into two parts, cutting out different colors of Luxe Leather.

Cut layers one and three together and layers two and four together.

Start with an open 4mm jump ring, and slide on the cut tree layers in order.

Close the jump ring by holding two pairs of pliers on each side of it and twisting the wrists.

Slide the closed jump ring (holding the layers) and an earring wire onto the 2mm jump ring. Close the ring.

One earring is done, repeat for the second.

I absolutely love these earrings and can't wait to show them off!

Bow Ring

Supply List

• Laser Cutting Machine
• Holiday Jewelry Bundle
• Luxe Leather Crimson Blaze
• Sizable Ring Base
• E600 Glue

Luxe Leather is compatible with the CO2 and Diode lasers.

Instructions

Upload the file to your laser machine software.

Cut the black lines and engrave the blue lines on a low-power and high-speed setting.

The blue line should not be cut all the way through; it is meant to mark the center of the strips.

Only the 5 strips with the score line will be glued and folded.

Apply glue to the strip where the score line is.

Fold an end and flip before securing it to the glue. This will create a cone shape at the end of the strip.

Fold and flip the other end of the strip and bring the ends together over that center scoreline.

Use a clip to hold the strip while it dries.

Repeat for the other strips, leaving the last piece alone for now.

After the strips have dried, glue the three larger strips together and the two smaller.

Use a clamp again to hold them together while they dry.

Take the remaining strip and create a small loop.

This will fit on top of small strips, so it doesn't need to be very big.

Once the layers are dried, apply glue to the center of the larger piece and stack the smaller piece. Clamp together until dried.

Glue the center loop into place.

Apply a large glob of glue to the ring face and press it into the back of the bow. Let the glue dry completely before wearing the ring.

This ring is probably my favorite piece we made today. I am so excited to wear it!

More Vogue Element Collections

All of these pieces of jewelry were so much fun to make!

But there are even more Vouge Element materials to choose from!

All of these materials are double-sided, are 1/16-inch thick, and are perfect for jewelry making!

Cozy Winter Collection

Winter Wonderland Collection

Elegant Christmas Collection

All of these laser materials are simply beautiful!